How to power a camera or Wi-Fi access point over Ethernet

Security camera with an Ethernet cable running to a blue network jack
Contents
  1. Connect one device with an injector
  2. Match the port to the device
  3. Check the power budget before you fill the ports
  4. Frequently asked questions

Power over Ethernet (PoE) carries power and data over one Ethernet cable. Mount a PoE camera above your garage door and you can power it from inside the house. If your router has ordinary Ethernet ports, keep it. An injector adds power to a single cable run. A PoE switch can power several devices, provided they fit within its power budget.

Connect one device with an injector

Put the injector near the router and a power outlet. Run a cable from a LAN port on your router to DATA IN on the TP-Link TL-POE160S injector. Connect the camera cable to PWR+DATA OUT, then plug the injector into the outlet. This arrangement also works for a compatible ceiling-mounted Wi-Fi access point. TP-Link injector connection diagram

For several devices, use a PoE switch. On the TP-Link TL-SG1005P V5, connect a LAN port on your router to port 5 on the switch. Plug the cameras or access points into ports 1 through 4. Port 5 carries data only. A camera that relies on PoE will stay off if you plug it into that port. TP-Link switch installation guide · What a switch does on a home network

Match the port to the device

Look up the PoE input on the device’s spec sheet. An 802.3af (PoE) port supplies up to 15.4 W at the switch, with 12.95 W available at the device after cable losses. For 802.3at (PoE+), those figures are 30 W and 25.5 W. If a camera requires 25 W at its input, look for a compatible PoE+ port. A basic PoE port falls short even before cable losses. NETGEAR’s PoE power guide

For 802.3bt (PoE++), check the type as well. Type 3 supplies up to 60 W at the switch and Type 4 up to 90 W. If the device specifies passive PoE, use the adapter its manufacturer lists. For example, TP-Link’s POE4824G is intended for compatible 48 V passive devices. The shape of the Ethernet jack alone cannot establish compatibility. TP-Link’s guide to PoE standards · Example of a 48 V passive adapter

Need the login details for your router? Look up the default IP address, username and password for your brand.

Find your router’s default login

Check the power budget before you fill the ports

On the TL-SG1005P V5, each of the four powered ports can supply up to 30 W, and all four share 65 W. Check the model label. The similarly named TL-SG1005LP in the same guide also offers 30 W per port, but shares just 40 W across them. TP-Link switch specifications

Suppose each camera needs the full PoE+ allowance. Budget 30 W per camera at the switch, including cable losses. Here’s how many the 65 W model can support at that allowance.

Planned devicesPower to reserve at the switchResult on this 65 W switch
Two2 × 30 W = 60 W5 W left across the two unused powered ports
Three3 × 30 W = 90 W25 W short, even with a fourth port free

The 5 W left over is a planning figure. The cameras may draw less in use. To size your own switch, add up the switch-side power allocations for your devices. If you need a third 30 W port in this example, use a compatible injector for that camera or choose a switch with at least 90 W of total PoE power and three PoE+ ports.

Frequently asked questions

Can I plug my laptop into a spare PoE switch port?

Yes, if it’s a standards-based PoE port. The switch checks for a compatible powered device before it applies power. An ordinary laptop gets a data connection and continues to use its own battery or charger, so it can use one of the spare ports in the example above. TP-Link’s explanation of device detection

Sources